Key takeaways
- See the best magnetic drills for steel work, with magnet strength, boring capacity, and speed specs for fab shops, site work, and structural jobs.
What's inside
- Quick Answer
- How to Choose
- VEVOR Magnetic Drill Press, 1300W, 1.57-Inch Boring Diameter, with 11 Drill Bits
- VEVOR Magnetic Drill Press, 1400W, 2-Inch Boring Diameter, 10-Speed, with 6 Drill Bits
- DEWALT DWE1622K Magnetic Drill Press Kit, 2-Inch, 10-Amp, 2-Speed
- Hougen HMD904 115-Volt Magnetic Drill
- ZELCAN 1550W Magnetic Drill Press with 6 Drill Bits, 2-Inch Boring Diameter
- Who Should Skip It
- FAQ
- Final Verdict
- Quick Answer
- How to Choose
- VEVOR Magnetic Drill Press, 1300W, 1.57-Inch Boring Diameter, with 11 Drill Bits
- VEVOR Magnetic Drill Press, 1400W, 2-Inch Boring Diameter, 10-Speed, with 6 Drill Bits
- DEWALT DWE1622K Magnetic Drill Press Kit, 2-Inch, 10-Amp, 2-Speed
- Hougen HMD904 115-Volt Magnetic Drill
- ZELCAN 1550W Magnetic Drill Press with 6 Drill Bits, 2-Inch Boring Diameter
- Who Should Skip It
- FAQ
- Final Verdict
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Magnetic Drills for Steel: 5 Portable Picks 2026
A magnetic drill goes where a drill press cannot: onto the beam, the plate, or the frame itself. It locks to the steel with an electromagnet base and drills clean, accurate holes with annular cutters, which is why structural and fabrication crews reach for one whenever a part is too big, too heavy, or already installed.
This guide compares five mag drills that cover the range from budget shop units to a pro-grade kit. The details that matter are magnet holding force, boring capacity, speed options, and weight, since these tools get carried, clamped overhead, and trusted to stay put under load.
As an Amazon Associate, we earn from qualifying purchases.
What we cover
- Quick Answer
- How to Choose
- VEVOR Magnetic Drill Press, 1300W, 1.57-Inch Boring Diameter, with 11 Drill Bits
- VEVOR Magnetic Drill Press, 1400W, 2-Inch Boring Diameter, 10-Speed, with 6 Drill Bits
- DEWALT DWE1622K Magnetic Drill Press Kit, 2-Inch, 10-Amp, 2-Speed
- Hougen HMD904 115-Volt Magnetic Drill
- ZELCAN 1550W Magnetic Drill Press with 6 Drill Bits, 2-Inch Boring Diameter
- Who Should Skip It
- FAQ
- Final Verdict
Quick Answer
The DEWALT DWE1622K is the pro-grade pick with a 10-amp motor, two speeds, and a quick-change arbor. VEVOR’s 1300W and 1400W models deliver strong magnet force and included cutter sets for less outlay, the Hougen HMD904 is the lightweight veteran, and ZELCAN’s 1550W unit adds a reversible drive.
How to Choose
Magnet force is the safety spec. The base has to hold the drill against feed pressure and cutter torque, including on vertical and overhead work. Look for holding force figures in the range these five models offer, and remember that thin steel reduces grip: the magnet needs enough material beneath it to develop full force, so very thin plate may need a thicker steel backing plate clamped behind it.
Match capacity to your cutters. Boring diameter tells you the largest annular cutter the drill can turn. A 1-1/2 to 2-inch capacity covers most structural connection work. Depth of cut matters too; most of these drills handle cutters up to 2 inches deep.
Annular cutters do the real work. Unlike twist bits, annular cutters cut only the rim of the hole and eject a solid slug, so they drill large holes faster with less power and leave a cleaner finish. Most mag drills use a 3/4-inch Weldon shank. Some kits add a keyed chuck for twist bits, which is handy for small holes and tapping-adjacent tasks.
Speed and weight. A single speed around 450 RPM suits mid-size cutters. Two-speed and variable-speed models widen the cutter range you can run well. Weight decides how the tool feels on a ladder or a column face; lighter drills around the 30-pound mark are far easier to position overhead.
VEVOR Magnetic Drill Press, 1300W, 1.57-Inch Boring Diameter, with 11 Drill Bits
This VEVOR unit is the value entry into mag drilling, and it arrives ready to cut: the box includes 11 annular cutter bits, so there is no separate cutter order before the first job. The 1300W motor turns cutters up to 1.57 inches in diameter at 810 RPM, and the electromagnetic base is rated at 2,922 pounds of holding force, which is serious grip for a tool at this level.
The single fixed speed runs faster than the pro drills in this guide, which favors smaller cutters; pace your feed on larger diameters and use cutting fluid generously. For a fab shop adding its first mag drill for frame and plate work on the flat, this package covers the essentials with the fewest extra purchases. Weldon-shank cutters keep bit changes simple.
Specs
| Spec | Value |
|---|---|
| Motor | 1300W |
| Max boring diameter | 1.57 inches |
| Magnetic force | 2,922 lbf |
| Speed | 810 RPM |
| Included | 11 annular drill bits |
| Shank | Weldon |
VEVOR Magnetic Drill Press, 1400W, 2-Inch Boring Diameter, 10-Speed, with 6 Drill Bits
The larger VEVOR steps capacity up to a full 2-inch boring diameter and adds a 10-speed gearbox, so you can slow the cutter down for big diameters in thick steel or speed it up for small holes. The 1400W motor and the same 2,922 pounds of magnetic holding force give it the muscle and grip for structural work, and six annular bits are included to start cutting right away.
A quick-release arbor speeds up cutter swaps when a job mixes hole sizes. This is the pick for shops that want one mag drill to span small bracket holes and large connection holes without owning two machines. As with its smaller sibling, keep cutting fluid on the cutter and let the tool’s weight do the feeding on horizontal work.
Specs
| Spec | Value |
|---|---|
| Motor | 1400W |
| Max boring diameter | 2 inches |
| Magnetic force | 2,922 lbf |
| Speed | 810 RPM max, 10 speed settings |
| Included | 6 annular drill bits |
| Arbor | Quick-release |
DEWALT DWE1622K Magnetic Drill Press Kit, 2-Inch, 10-Amp, 2-Speed
The DWE1622K is the professional standard in this group. Its 10-amp motor drives a two-speed gearbox, 300 RPM for large cutters and 450 RPM for smaller ones, which is the right spread for annular cutting in steel. Capacity is 2 inches, drill travel is a generous 4-3/8 inches, and the quick-change system swaps between the 3/4-inch Weldon arbor and the included 1/2-inch keyed chuck without tools.
Details show the jobsite intent: overload protection guards the motor when a cutter binds, the coolant tank feeds cutting fluid to the cut, and the kit case keeps it organized between jobs. For crews drilling structural connections daily, this is the drill that justifies itself through speed, durability, and cutter life. It is the benchmark the budget models are measured against.
Specs
| Spec | Value |
|---|---|
| Motor | 10-amp |
| Speeds | 2 speeds, 300 and 450 RPM |
| Annular capacity | 2 inches |
| Drill travel | 4-3/8 inches |
| Arbor | Quick-change, 3/4-inch Weldon |
| Extras | 1/2-inch keyed chuck, coolant tank, overload protection |
Hougen HMD904 115-Volt Magnetic Drill
Hougen helped define the portable mag drill, and the HMD904 is its lightweight workhorse. It runs on 115 volts with an 8-amp motor at a single 450 RPM, a speed well matched to its 7/16-inch to 1-1/2-inch annular capacity and 2-inch depth of cut. The two-stage magnet is easy to position: a weaker hold lets you slide the drill into alignment on your mark, then full power locks it down.
At under 30 pounds, it is the easiest drill here to carry up a ladder or hold against a column while the magnet engages. The slot-drive arbor takes standard 3/4-inch shank cutters. Fabricators who drill mostly mid-size holes and value a light, proven tool over maximum capacity will keep reaching for this one. It has been a shop staple for years for good reason.
Specs
| Spec | Value |
|---|---|
| Power | 115V, 8-amp motor |
| Speed | 450 RPM |
| Capacity | 7/16 to 1-1/2 inch annular cutters |
| Depth of cut | 2 inches |
| Magnet | Two-stage |
| Arbor | 3/4-inch slot drive |
ZELCAN 1550W Magnetic Drill Press with 6 Drill Bits, 2-Inch Boring Diameter
The ZELCAN brings the strongest paper specs among the budget models: a 1550W motor, 2-inch boring capacity, and 3,125 pounds of magnetic holding force, the highest figure in this guide. Speed is stepless up to 650 RPM, so you can trim the pace to the cutter size, and the drive is reversible, which helps when backing cutters out of deep holes or running threading tools at low speed.
Six drill bits are included in the box. For shops that drill thick plate and want maximum magnet grip without moving to pro-brand money, this is a compelling package. Keep expectations aligned with the segment: fit and finish trail the DEWALT and Hougen, but the core numbers, motor, magnet, and capacity, are all where a steel shop needs them.
Specs
| Spec | Value |
|---|---|
| Motor | 1550W |
| Max boring diameter | 2 inches |
| Magnetic force | 3,125 lbf |
| Speed | Up to 650 RPM, stepless |
| Direction | Reversible |
| Included | 6 drill bits |
Who Should Skip It
Skip the mag drill if your drilling is all small parts at the bench, where a drill press is cheaper, more rigid, and faster to set up. The magnet only holds on ferrous steel, so aluminum, stainless in many grades, and non-metal work need a different solution such as a vacuum base or clamping fixture. On steel thinner than about a quarter inch, magnet grip drops off sharply; either back the work with a thick steel plate or drill it on the press instead. Always use the safety chain on vertical and overhead work.
FAQ
How thick does steel need to be for a magnetic drill?
Full holding force needs roughly 3/8 inch or more of steel under the base. Thinner material still works if you clamp a thick steel plate behind it to give the magnet more iron to hold. Never trust the magnet alone on thin sheet.
Can a magnetic drill use regular twist bits?
Many can, with a keyed chuck adapter like the one in the DEWALT kit. Twist bits are fine for small holes, but annular cutters are faster, cleaner, and easier on the motor for holes above about 1/2 inch.
What is an annular cutter?
It is a hollow cutter that machines only the edge of the hole and drops out a solid slug, instead of turning the whole hole into chips. That efficiency is why a portable mag drill can cut 2-inch holes that would stall a hand drill.
Do I need cutting fluid with a mag drill?
Yes, for steel. Fluid cools the cutter, extends its life, and improves hole finish. Several of these drills include a gravity-feed coolant tank; otherwise apply fluid from a bottle as you cut, and clear slugs between holes.
Final Verdict
For daily professional work, the DEWALT DWE1622K is the clear first choice, with the Hougen HMD904 close behind for anyone who prizes light weight and a proven track record. The two VEVOR models make mag drilling accessible to smaller shops, the 1400W version being the more versatile, and the ZELCAN 1550W is the budget pick when maximum magnet force and capacity top the list. Choose by the largest cutter you run and how often the drill leaves the bench.
Related guides
Keep reading
- Best Drill Presses for Metalworking: 5 Picks for 2026
- Best Magnetic Welding Ground Clamps: 5 Picks for 2026
- Best Welding Boots for Women: Steel Toe Picks That Fit
- Tietoc 22 Piece Flexible Drill Bit Extension Set Review
- Best Hole Saws for Metal: 5 Bi-Metal Kits That Cut Clean
- Best Metal Files: 5 Nicholson and Needle File Picks
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.
Write Your Review
No reviews yet. Be the first to share your experience!