Updated Nov 19, 2026· 10 min read

Key takeaways

  • Compare the best magnetic welding ground clamps from Magswitch, Hobart, Bessey and Mag-Mate by amp rating, holding force and switch type before you buy.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

A magnetic welding ground clamp replaces the spring jaws of a standard work clamp with a magnet that seats flat against the workpiece, so the ground connection is made by placing the clamp on clean steel and, on switchable models, twisting a knob. The best all-around choice for most shops is the Magswitch 300 Amp Ground Clamp (8100746), because it pairs a 300 amp rating with a fully switchable magnet, a finned housing that sheds heat, and a base that works on flat plate and pipe alike. For higher-output machines, the Hobart 770566 raises the rating to 500 amps, and the Bessey MGC-2 covers heavy work at 800 amps, while the Mag-Mate WG300R and the Bessey MGC-1 fill the mid-range and budget ends of the lineup.

As an Amazon Associate, we earn from qualifying purchases.

What we cover
  1. Table of Contents
  2. Quick Picks
  3. 1. Magswitch 300 Amp Ground Clamp (8100746)
  4. 2. Hobart 770566 500-Amp Magnetic Ground Clamp
  5. 3. Mag-Mate WG300R Magnetic Welding Ground
  6. 4. Bessey MGC-2 Magnetic Ground Clamp
  7. 5. Bessey MGC-1 Magnetic Ground Clamp
  8. How to Choose a Magnetic Welding Ground Clamp
  9. FAQ
  10. Conclusion

Table of Contents

Quick Picks

  • Best overall: Magswitch 300 Amp Ground Clamp (8100746), premium tier — switchable magnet, finned cooling housing, 90 lb breakaway force.
  • Best for higher-output machines: Hobart 770566, mid-range tier — 500 amp rating with a quick-release magnet.
  • Best on/off control at 300 amps: Mag-Mate WG300R, mid-range tier — rare earth magnet rated at 150 lb of holding force.
  • Best for heavy-duty current: Bessey MGC-2, premium tier — 800 amp grounding capacity with a copper stud.
  • Best budget pick: Bessey MGC-1, budget tier — 250 amp capacity sized for light-duty machines.

1. Magswitch 300 Amp Ground Clamp (8100746)

Check price on Amazon

The Magswitch 8100746 is the reference design in this category: a switchable magnetic ground that turns fully on and off with a twist of the top knob. Switching the magnet off releases the clamp without prying and lets grinding dust and chips fall away instead of building up on the contact face, which keeps the electrical contact cleaner from one job to the next. The published magnet strength is 90 lb of breakaway force, and the base is shaped to ground on a flat surface or on pipe, so it covers plate, sheet, and round stock in the same shop.

Heat is the other detail Magswitch addresses directly. The housing carries a finned design that the manufacturer rates as lowering the temperature of the unit by almost 27 percent compared with the earlier unfinned design, which matters on long welds where a hot ground clamp loses contact quality. At 0.8 lb net weight and 2.3 inches of overall height, it is also the easiest clamp here to move around a crowded bench. It sits in the premium tier, and the combination of the switchable magnet, the cooling fins, and the 300 amp rating makes it the default recommendation for MIG, TIG, and stick work at typical shop amperages.

Specs

  • Model: 8100746
  • Current rating: 300 amps
  • Magnet strength: 90 lb (40 kg) breakaway force
  • Magnetic pole footprint: 40 mm diameter
  • Overall height: 2.3 in (57.3 mm)
  • Net weight: 0.8 lb
  • Magnet control: fully switchable on/off twist knob
  • Surfaces: flat steel and pipe
  • Housing: finned design for heat dissipation

2. Hobart 770566 500-Amp Magnetic Ground Clamp

Check price on Amazon

The Hobart 770566 steps the current rating up to 500 amps, which makes it the natural pick for welders running larger MIG and stick machines that would push a 250 or 300 amp ground past its rating. Hobart describes the magnet as a quick-release design, so the clamp lifts off the workpiece with a lever action rather than a straight pull against the full holding force. That matters at 500 amp size, because a magnet strong enough to stay put under a heavy cable needs a release mechanism to be practical.

Published weight is 1.54 lb, light enough to hang from the ground lead without dragging the cable around the bench. The ground cable attaches to the clamp stud with a lug, the same connection style used across this category, so it drops into an existing lead setup without adapters. As a mid-range tier option from a major welding brand, the 770566 is the straightforward choice when the machine output, rather than switchable-magnet convenience, is the deciding factor.

Specs

  • Model: 770566
  • Current rating: 500 amps
  • Weight: 1.54 lb
  • Magnet: quick-release design
  • Connection: stud terminal for a ground cable lug
  • Brand: Hobart (ITW Welding)
  • Surfaces: flat ferrous steel

3. Mag-Mate WG300R Magnetic Welding Ground

Check price on Amazon

The Mag-Mate WG300R, made by Industrial Magnetics, is a 300 amp ground built around a rare earth neodymium magnet with a published holding force of 150 lb, the strongest hold figure in this roundup relative to its amp class. Like the Magswitch, it uses an on/off switch for attachment and release, so the magnet face can be wiped clean between jobs and the clamp does not collect chips while it sits in a toolbox.

The base is designed for flat surfaces and for pipe, and the operating manual for the Mag-Mate ground clamp line specifies placing the clamp at least three inches from the weld point and keeping the contact area clean for proper current flow. A copper or brass stud on top of the housing takes the ground cable lug. In the mid-range tier, the WG300R is the pick for buyers who want switchable control and a high holding-force rating from an industrial magnetics manufacturer rather than a welding brand.

Specs

  • Model: WG300R
  • Current capacity: 300 amps
  • Holding force: 150 lb
  • Magnet type: rare earth (neodymium)
  • Magnet control: on/off switch
  • Surfaces: flat surfaces and pipe
  • Connection: stud terminal for a ground cable lug
  • Manufacturer: Industrial Magnetics (Mag-Mate)

4. Bessey MGC-2 Magnetic Ground Clamp

Check price on Amazon

The Bessey MGC-2 carries the highest grounding capacity in this roundup at 800 amps, aimed at heavy fabrication and high-output industrial machines. The magnet is a round cup design measuring 3-1/2 inches in diameter and 2 inches high, with a published pull force of 55 lb. The cable connection is a copper stud, chosen for conductivity at sustained high current.

Unlike the switchable models above, the MGC-2 uses an always-on permanent magnet, which keeps the design simple and eliminates moving parts; the trade-off is that the face collects ferrous debris and needs regular wiping, and removal takes a direct pull or a slide off the edge of the workpiece. In the premium tier, it suits shops that run big machines on thick plate and want a ground rated well above the machine output so heat buildup at the contact point stays low.

Specs

  • Model: MGC-2
  • Grounding capacity: 800 amps
  • Magnet shape: round cup
  • Diameter: 3-1/2 in
  • Overall height: 2 in
  • Pull force: 55 lb
  • Stud material: copper
  • Magnet control: always-on permanent magnet

5. Bessey MGC-1 Magnetic Ground Clamp

Check price on Amazon

The Bessey MGC-1 is the smaller clamp in Bessey’s magnetic ground line, rated at 250 amps. That capacity matches the machines it is meant for: compact MIG welders, small inverter stick welders, and light TIG work in home and maintenance shops. Staying inside the rating matters more with magnetic grounds than with jaw clamps, because excess current heats the contact face and weakens both the connection and the magnet’s hold.

The MGC-1 follows the same round cup, always-on permanent magnet layout as its larger sibling, in a smaller and lighter package that is easier to seat on narrow flanges and small parts where a 3-1/2 inch cup will not sit flat. As the budget tier pick, it is the sensible ground for a light-duty machine that will never approach the ratings of the bigger clamps, and it keeps a matched brand and connection style for shops already running Bessey clamping gear.

Specs

  • Model: MGC-1
  • Grounding capacity: 250 amps
  • Magnet shape: round cup
  • Magnet control: always-on permanent magnet
  • Connection: stud terminal for a ground cable lug
  • Brand: Bessey
  • Intended machines: light-duty MIG, stick, and TIG welders

How to Choose a Magnetic Welding Ground Clamp

Match the amp rating to the machine. The ground clamp carries the full welding current back to the machine, so its rating should meet or exceed the highest output the welder will actually run. A clamp run past its rating overheats at the contact face, which raises resistance, destabilizes the arc, and can permanently weaken the magnet. When in doubt, step up one size; an oversized ground runs cooler and lasts longer.

Decide between switchable and always-on magnets. Switchable models such as the Magswitch and the Mag-Mate turn the magnetic field off for release, which makes repositioning fast and keeps the contact face clean, since debris falls away when the field is off. Always-on clamps such as the Bessey MGC line are simpler and have no mechanism to wear, but they attract chips constantly and need the face wiped before every use to keep contact resistance low.

Check the surface, not just the rating. Magnetic grounds only work on ferrous steel. They will not hold on aluminum or on austenitic stainless grades such as 304 and 316, and hold strength drops sharply on painted, rusty, or scaled surfaces because the coating creates an air gap. Published breakaway and pull figures assume clean, flat, adequately thick steel; thin sheet gives the magnet less material to saturate and holds less. For pipe and round stock, look for a base with a V-groove or a pole shape that seats on curved surfaces.

Confirm the cable connection. Every clamp here takes the ground lead through a stud and lug. Check that the stud size suits the lug on the existing lead and that the cable gauge itself is rated for the machine’s amperage and lead length, since an undersized cable causes the same heating problems as an undersized clamp.

Place it close, but not too close. A ground placed near the weld keeps the current path short and the arc stable. Manufacturer guidance for magnetic grounds specifies keeping the clamp at least three inches from the weld point to avoid overheating the magnet, and keeping the contact patch clean and fully seated before striking an arc.

FAQ

Can a magnetic ground clamp fully replace a spring ground clamp?

For flat ferrous steel, yes, a magnetic ground can serve as the only work clamp, and it is often faster to place. A spring clamp is still worth keeping in the shop because it grips edges, thin material, and non-magnetic metals such as aluminum, where a magnetic ground cannot hold at all. Many shops run one of each and pick based on the workpiece.

Do magnetic welding ground clamps work on aluminum or stainless steel?

No. Magnetic grounds require a ferromagnetic workpiece, which limits them to carbon steel and other magnetic alloys. Aluminum is non-magnetic, and common austenitic stainless grades such as 304 and 316 are effectively non-magnetic as well. For those metals, a jaw-style ground clamp is the correct connection.

What amp rating should I choose for a magnetic ground clamp?

Choose a rating at or above the maximum output of the welder it will serve. A 250 amp clamp suits compact home-shop machines, 300 amps covers most mid-range MIG and stick work, and 500 to 800 amp models match high-output shop and industrial machines. Running a clamp above its rating causes heat buildup at the contact face and degrades both contact quality and magnet strength.

Why does a magnetic ground clamp lose hold or get hot during a weld?

The usual causes are a dirty or coated contact surface, a workpiece too thin for the magnet to saturate, or current above the clamp’s rating. Paint, rust, and mill scale all create resistance and an air gap. Cleaning the contact patch to bare metal, seating the full magnet face, and stepping up to a higher-rated clamp resolve most cases.

Conclusion

Magnetic ground clamps trade the bite of spring jaws for placement speed and a broad, flat contact patch on steel. The Magswitch 8100746 is the best fit for most welders, combining a 300 amp rating, a fully switchable magnet, and a finned housing in the premium tier. The Hobart 770566 and the Mag-Mate WG300R cover the mid-range with 500 and 300 amp ratings respectively, the Bessey MGC-2 handles heavy 800 amp work, and the Bessey MGC-1 keeps light-duty setups in the budget tier. Matching the rating to the machine and keeping the contact face clean are the two decisions that determine how well any of them performs.

H
Hoodlum Welding Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Magnetic Welding Ground Clamps: 5 Picks for…Check price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.