Key takeaways
- Compare the best drill presses for metalworking, from compact benchtop models to a full floor press, with chuck, speed, and swing specs for each pick.
What's inside
- Quick Answer
- How to Choose
- JET JDP-15M 3/4-HP 15-Inch Bench Drill Press
- WEN 4212T 5-Amp 10-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser
- WEN 4214T 12-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser and Work Light
- SHOPMAX SD0813 8-Inch Benchtop Drill Press
- Shop Fox W1680 1-Horsepower 17-Inch Floor Model Drill Press
- Who Should Skip It
- FAQ
- Final Verdict
- Quick Answer
- How to Choose
- JET JDP-15M 3/4-HP 15-Inch Bench Drill Press
- WEN 4212T 5-Amp 10-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser
- WEN 4214T 12-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser and Work Light
- SHOPMAX SD0813 8-Inch Benchtop Drill Press
- Shop Fox W1680 1-Horsepower 17-Inch Floor Model Drill Press
- Who Should Skip It
- FAQ
- Final Verdict
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Drill Presses for Metalworking: 5 Picks for 2026
A drill press earns its place in a metal shop by doing the one thing a hand drill cannot: putting holes exactly where you marked them, square to the work, at a controlled feed rate. For welders and fabricators, that means clean holes in tube, plate, and angle iron without wandering bits or ovaled bores that ruin fit-up.
This guide compares five presses that suit metalwork, from compact 8-inch benchtop models that fit a crowded fab bench to a full-size floor press for heavy plate. Each pick lists the motor, swing, chuck, and speed details that matter most when the bit meets steel.
As an Amazon Associate, we earn from qualifying purchases.
What we cover
- Quick Answer
- How to Choose
- JET JDP-15M 3/4-HP 15-Inch Bench Drill Press
- WEN 4212T 5-Amp 10-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser
- WEN 4214T 12-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser and Work Light
- SHOPMAX SD0813 8-Inch Benchtop Drill Press
- Shop Fox W1680 1-Horsepower 17-Inch Floor Model Drill Press
- Who Should Skip It
- FAQ
- Final Verdict
Quick Answer
For most small fab shops, the WEN 4212T hits the sweet spot with a 10-inch swing, variable speed, and a laser guide. Tight benches are better served by the SHOPMAX SD0813, the JET JDP-15M brings a 15-inch swing to the bench, and the Shop Fox W1680 floor press handles the heavy plate work the benchtop models cannot.
How to Choose
Start with swing. Swing is twice the distance from the spindle center to the column, and it sets the widest stock you can center a hole in. An 8-inch press centers holes in material up to 8 inches wide, which covers brackets, tabs, and small plates. Frames, gates, and machine bases call for 12 inches of swing or more.
Speed range matters more for metal than for wood. Large bits in steel want slow spindle speeds, while small bits in aluminum can run fast. A press with electronic variable speed lets you dial in the right pace as bit sizes change through the day. A belt-stepped press works too, but you will change belt positions often if you switch bit sizes a lot.
Check the chuck and spindle travel. A 1/2-inch keyed chuck covers most jobber bits used in fabrication. Spindle travel tells you how deep you can drill in one pass; 2 inches handles plate and tube walls easily, while longer travel helps with thick stock and stacked parts.
Benchtop or floor model. Benchtop presses save floor space and suit most bracket and plate work. A floor press adds swing, height capacity, and mass, which pays off when you drill large parts or run big bits all day. Cast iron tables and bases on either style help keep vibration down and holes accurate.
JET JDP-15M 3/4-HP 15-Inch Bench Drill Press
The JDP-15M is the premium benchtop in this group, a 15-inch press from JET’s long-running 354165 line that brings near floor-model capacity to a bench footprint. Its 3/4-horsepower motor drives 16 belt-selected speeds from 200 to 3,630 RPM, the widest range here, so you can slow down for large bits in plate or spin up for small holes in sheet without swapping machines.
That slow bottom end is what metalworkers actually buy this press for: large bits in steel want torque at low RPM, and the 200 RPM floor gives you room the smaller presses do not. The 15-inch swing centers holes in stock that would hang off an 8- or 10-inch press, and the heavy construction keeps the machine settled under feed pressure.
It gives up the lasers and digital readouts of the WEN variable-speed models, and it is a heavier lift when bench layouts change. What you get instead is a simple, durable belt-drive press from an industrial line, sized for shops that drill steel daily and want one benchtop machine that rarely feels undersized.
Specs
| Spec | Value |
|---|---|
| Motor | 3/4 HP |
| Swing | 15 inches |
| Speeds | 16 speeds, 200 to 3,630 RPM |
| Model | 354165 (JDP-15M) |
| Type | Benchtop |
WEN 4212T 5-Amp 10-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser
The 4212T is the step up most metalworkers should look at first. Instead of moving a belt between pulleys, you turn a dial to set any speed from 530 to 3,100 RPM, and a digital readout shows the current setting. That matters in a fab shop, where one job might need a slow, torquey hole in plate and the next a fast hole in thin aluminum.
The 10-inch swing centers holes in wider stock than the 8-inch models, and spindle travel grows to 2-3/8 inches. A crosshair laser lines the bit up with your center-punch marks, which speeds up repetitive bracket work. The motor is rated at 5 amps on the listing, giving it more low-speed push than the smaller WEN. If your bench drilling mixes bit sizes all day, this is the convenience pick that still keeps a cast iron table and a compact footprint.
Specs
| Spec | Value |
|---|---|
| Motor | 5-amp |
| Swing | 10 inches |
| Speed range | 530 to 3,100 RPM, variable |
| Chuck | 1/2-inch keyed, JT33 taper |
| Spindle travel | 2-3/8 inches |
| Guide | Crosshair laser |
WEN 4214T 12-Inch Variable Speed Cast Iron Benchtop Drill Press with Laser and Work Light
The 4214T stretches the benchtop format to a 12-inch swing, which opens up wider plates and panels that would not fit under the smaller presses. It keeps the variable speed drive, here spanning 580 to 3,200 RPM, and adds both the crosshair laser and an adjustable work light for dim corners of the shop.
Spindle travel is the other headline: 3-1/8 inches lets you drill through thicker stock, stacked plates, or a part held in a fixture without repositioning. The 5-amp motor and 1/2-inch chuck match the 4212T, so the upgrade here is capacity and visibility rather than raw power. For a benchtop-only shop that regularly drills larger workpieces, this is the most capable option in the WEN benchtop range and the one least likely to be outgrown quickly.
Specs
| Spec | Value |
|---|---|
| Motor | 5-amp |
| Swing | 12 inches |
| Speed range | 580 to 3,200 RPM, variable |
| Chuck | 1/2-inch keyed, JT33 taper |
| Spindle travel | 3-1/8 inches |
| Extras | Crosshair laser, work light |
SHOPMAX SD0813 8-Inch Benchtop Drill Press
The SD0813 comes from SHOPMAX, the bench-tool line of YARDMAX, and it competes directly with the smallest WEN. Its 4.2-amp motor is the stronger of the two at this size, and its nine speed settings span 500 to 3,200 RPM. That slower 500 RPM low end is useful for metal, since larger bits in steel cut better and last longer at lower speeds.
It pairs an 8-inch swing with a 1/2-inch keyed chuck and 2 inches of spindle travel, so it suits bracket, tab, and small-plate work. The wider speed selection gives it an edge when you move between steel and aluminum during the day. Choose it if you want more motor and more speeds in a compact footprint, and you do not need a laser guide.
Specs
| Spec | Value |
|---|---|
| Motor | 4.2-amp |
| Swing | 8 inches |
| Speeds | 9 speeds, 500 to 3,200 RPM |
| Chuck | 1/2-inch keyed |
| Spindle travel | 2 inches |
| Model | SD0813 |
Shop Fox W1680 1-Horsepower 17-Inch Floor Model Drill Press
When benchtop throat depth runs out, a floor press is the answer, and the W1680 is the classic shop-floor option in this group. Its 1-horsepower motor and 17-inch swing handle the wide, heavy workpieces that define fabrication work: gate frames, machine bases, trailer parts, and long plates that need holes far from an edge.
Standing on its own base, it also frees your bench entirely and gives you height capacity for tall parts held upright. The trade-offs are floor space and the commitment of a permanent spot in the shop layout. Listing data for this long-running model is thinner than for the newer benchtop presses, so the specs below stick to the headline figures. For a growing fab shop, this is the press that ends the workaround of clamping parts at odd angles on a too-small table.
Specs
| Spec | Value |
|---|---|
| Motor | 1 horsepower |
| Swing | 17 inches |
| Type | Floor model |
| Model | W1680 |
Who Should Skip It
Skip the drill press entirely if most of your drilling happens on assembled frames, installed parts, or out on site; a magnetic drill handles that work better. If you only drill thin sheet a few times a month, a hand drill with step bits is cheaper and takes no bench space. And if you are hoping to mill with one, stop here: drill presses are built for straight-down loads only, and side loads from milling will wear the bearings and spoil accuracy. Buy a mill for milling.
FAQ
What spindle speed should I use for drilling steel?
Larger bits need slower speeds. A small bit in mild steel can run near the top of these ranges, while a 1/2-inch bit should run at the slow end with steady feed pressure and cutting fluid. Variable-speed models make this easy to adjust as you change bits.
Can I mill metal with a drill press?
No. Drill press bearings and chucks are designed for downward force only. Side pressure from milling can loosen the chuck on its taper and damage the spindle. Use the press for drilling, reaming, and countersinking, and keep milling on a milling machine.
Is a benchtop or floor drill press better for a welding shop?
A benchtop press covers most bracket, tab, and plate work and leaves floor space free. A floor press earns its footprint when you regularly drill wide or tall parts, or run large bits for long stretches. Many shops start benchtop and add a floor model as work grows.
What chuck size do I need for metalworking?
A 1/2-inch chuck covers the jobber bits most fabrication uses. For larger holes, switch to reduced-shank bits that fit the 1/2-inch chuck, or use hole saws and annular cutters suited to the job rather than forcing oversize twist bits.
Final Verdict
For a single all-round benchtop press, the WEN 4212T offers the best mix of swing, variable speed, and guidance. The SHOPMAX SD0813 serves tight benches and light budgets. The JET JDP-15M is the premium benchtop step-up, and the Shop Fox W1680 remains the floor-standing answer for big fabrication work. Match the swing to the widest stock you drill, and any of the five will put holes where you marked them.
Related guides
Keep reading
- Best Magnetic Drills for Steel: 5 Portable Picks 2026
- Tietoc 22 Piece Flexible Drill Bit Extension Set Review
- Best Magnetic Welding Ground Clamps: 5 Picks for 2026
- Best Folding Welding Tables for Small Workshops 2026
- Best Deburring Tools for Metal: 5 Swivel Picks for Shops
- Best Hole Saws for Metal: 5 Bi-Metal Kits That Cut Clean
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.
Write Your Review
No reviews yet. Be the first to share your experience!